Tetrahedron Resonance
[This is a document never released as the model was backwards.
Radiant Light travels in a straight line and EM field photons travel in circles.
To create EM fields we must use radiant photons and pull them into electron shells to raise the E field.
Radiant light is a scalar cancelled linear force, and EM is a circular force.
Document does contain some intresting questions as to crystals.]
The model for magnetism under "magnetricity" failed during experiment, which led to the Light Techonology experiment and opened a new line of investigation.
This article was the begining of the search for aquiring power from the legs of the tetrahedron.
.
[reciprocator]
Ever since the experience of the ZPE coils and the realization that
there is ample energy around us everywhere, I have been drawn to
discovering just how this energy present, in oppositely spinning atoms
of Copper can be harnessed to produce a linear flow. In order to
channel a spin force into a linear force
we can look at the steam engine. The cylinders are kept out of phase
and thus the dead spot on reversals is overcome by the state of the
secondary spin interacting. [Dr Pajak] Applying this to electricity and
torsion we can have several resonant circuits interacting at
various angles and phases.
Why does putting pressure on a
crystal lattice create a voltage? We do not need the crystal in our
devices if we can harness the basic principle that crystals present to
us. Pressure [or tempic field] can create a voltage at the nodes or
vertexes of the form created by four atoms sharing electrons. There is
a current flow between the electron shells as electrons are shared
between them. Does the tempic field set this resonance off balance
to produce a one way or linear current in crystals? Crystals are our
model, but understanding the principle is the key to better designs.
The tetrahedron or star tetrahedron as an energy conversion system.
System was suggested by Kosol Ouch [intuitive] and first built by
John Nelson developing random voltages as high as 30 volts on Yahoo
Kosol Groups.
This document is presented as an in depth study and support material for designing a reliable system.
Resonance
If resonance is achieved of all three of the field forces in one coil
then a totally psychic energy substance will form, that can be directed
with mind. [Wilbert Smith]
Wilbert suggested a coil with correct spacing between windings on a ferrite core. Kosol suggests a tetrahedron form.
To get any appreciable electrical current from the design we recognized that resonance
would be important. Each leg of the tetrahedron would be set into
resonance of as many energy forms [TEM] as possible such that no energy
is lost. Tempic field is then considered to bring the system to Over
Unity emulating the structure of crystals. 6 phase resonance
of some kind would result with a tempic skew vibration, and also a
precessing magnetic field of some sort. A circuit that feels and acts
like a crystal would be the result.
Resonance of EM fields is well understood and both parallel and series
resonance can be studied to set up each leg of the circuit. Any one
surface of the tetrahedron forms into a 3 phase circuit as found in
current technology. A power transfer system known as Delta 3 phase
is being used all around us at present, but has never been presented as
a resonant system to capture tempic field energy, or used as a reciprocator.
The diagram represents two different ways to establish EM or sine coils
on an iron or steel tube to become resonant. Parallel coils receive a
capacitor across them, and series coils receive a capacitor off their
ends. The tips of the tetrahedron wrapped with spherical capacitors act
as series resonant systems with the coils on the legs. Either resonance
will create a reversing magnetic field in the legs or coils core, but
the parallel configuration will set up a separate electric energy
resonance on each leg only coupled to other legs by the magnetic field
in the structure if desired.
What is not covered well in current technology is the magnetic field
itself, how it propagates or appears at distance. Generally the coil
covers the entire single field of our devices and the magnetic field is
treated as a single unit. This is not the case however and if wound on
different core structures propagation of magnetic field becomes very important.
Also if we use the tempic field
to generate the vibrating electric nodes, as John has now shown us is
possible, then placing the correct EM resonant circuits between these
nodes would result in a self powering system on the EM side as well.
The energy may be coupled either electrically or magnetically.
Tanjmaster [John Nelson writes]
"I think I need to clarify here. You don't hook the sinoid coil to
the capacitor. You just put the cap in the zpe coil system field.
The reason I was getting only millivolt readings was because I had
hooked
the coils to the capacitors. The sinoid and bismuth coils are
hooked together but the ends should just remain open. When the capacitor
is in the field it will charge."
Johns original design and comments refers to the capacitors formed on
the spheres or tips of the tetrahedron form that charge up by only
setting in the intersecting fields of the coils, however if EM
resonance is present on each leg there would probably be substantially
more current availible. If these natural voltage nodes appearing, and
magnetic field nodes, intersect at the same points at device resonance,
we may expect actual power to emerge. While John has reported lighting
LEDs already, moving the device has shown that loosing the "space
conditioning charge" upsets the output for a time.
A very important measurement from this device is that of frequency.
While 60 hz is expected as well as harmonics of 60 hz like 120, the
device has been also producing frequencies approaching 400 hz at times
as well as interacting psychically. The tempic production of these EM
levels at specific frequencies could lead to the development of a fully
resonant system producing AC currents.
Magnetricity:
For placing coils on an iron core that is longer then the
coil, as we will have in the tetrahedron coil structure, and determining the best layout of coils for the legs.
The magnetic field off the ends of a coil has been documented. At some
distance the field will reverse and a dead spot or null point will be present between two
opposing fields both being energized by the same coil.
The fields will oppose one another and here is where electrons will
naturally collect as with orbital shells. The highest electric field
also is found to be off the ends of the coil. If copper is wrapped
around the iron core then this field will propagate along the iron rod
to some distance with little loss, and we have seen what opposing
fields do when they hit copper. For maximum transfer of energy the
copper or aluminum covering will appear between the coils but not under
them.
This will be a major factor for designing an efficient energy resonant
tetrahedron. If the coils on one leg of the system create nulls along the other
legs then no energy will be transferred between the coils. If the magnetic nulls
land on the tips of the form then energy will move easily between the coils actually reversing its polarity. If
copper is present along any exposed iron surfaces less energy will be lost.
Little has been documented as to how far between these points, or
how much current it will take to move them, but to establish a totally
resonant tetrahedron all three energies must be considered. A first
trial with resonant coils is necessary. Fire up one coil with the same
voltage and frequency you want your output EM to resemble. Now slide a
second resonant coil down the core and find the dead spot, if it exists
for these values it will cancel around the null where magnetic fields
reverse and equal on both sides of the coil. Now slide the coil away
and find the distance to maximum energy transfer between the coils.
Finally cut a copper tube the correct distance and slide it over the
null point on the iron core, to see if the energy transfer is
increased. At the magnetic null point is where scalar cancelling energy
is highest, as well we would expect electron counts to be raised here.
This point becomes one point or tip of the tetrahedron, and now
magnetic energy should be maximized to move between the coils
magnetically. Record all your parameters, such as coil winds, wire
lengths, capacitance, frequency and finally log the distance to nulls
and between coils for final design of the cores edge lengths.
Say we want an output of 12 volts at 400 hz, start with the resonance
tables and go from there, design the coils, size the caps. You will
then need a source of 12 volts at 400 hz to do the magnetic null
testing to find correct magnetic lengths of the cores. Place the source
on one coil, a scope or meter on the other coil and start expeimenting
for maximum energy transfer parameters.
In theory we could progress down the iron core of any length covering
the null points with copper tube and cause the energy to pop out
finally at one magnetic resonant point further down, or place coils
anywhere along the tube between the null points. [Magnetricity theory]
Also to create a perfectly balance iron copper resonance one would have
to find these points to determine the core length and cut it off
exactly where the magnetic fields reverse, totally removing any
opposing flows but utilizing all the available iron length. This would
produce maximized effects and interacions between the energy of the
iron and the copper, now cover the exposed ends of this coil core with
copper to reflect all energy back inwards.
"I have purposed using iron tie wires for the core material, ferrite would be better for higher frequencies.
Whatever material we use for the core of the iron tetrahedron we need
to first do some experiment with this material of only one leg and
determine where these dead spots are likely to form. Placing them
exactly at the tips, then covering them with copper should increase the
total system energy level bouncing between the coils. A more natural
flow of magnetricity should result.
The magnetic field will thus gyrate around the tetrahedron, always
controlled by at least one coil and thus it will never loose its
coherence as with ordinary coils cores. It is likely this will produce
some kind of precession overall, but most important it will continually
be aligning the coppers nuclear alignment so as to reduce electron
resistance due to induction. In a tunned circuit the Q factor is a
direct function of the Copper resistance encountered and decreases the
circuits ability to keep oscillating. While the tempic coils seem to
naturally charge themselves, the EM coils are constantly decaying their
increased energy states."
Preventing magnetic field collapse in coils that are at their electrical dead spot:
One way to lower the AC resistance in a coil is to set a magnet inside
or near it. Now the reverse inductive spin of the Proton shell is
aligned already and the energy to tilt the mass of the atoms to achieve current flow is reduced. The magnetic field prebiases the coil and breaks up the isotope chains
normally running the length of the wire from nucleus to nucleus. If the
coil now receive pulsed DC the induction should be much reduced
as the magnetic field never totally collapses. In the tetrahedron, if
the magnetic field nodes are kept on the tips of the core, then the
same effect should decrease copper losses on the EM side as each coil
in its high current state of oscillation will bias the entire core
system. All legs will thus have some magnetic field, either opposing or
aiding to maintain copper nuclear alignment off centered.
In the above experimental iron rod or tube, now place opposing magnets
on both ends of the iron core tube such that a null is formed at the
coils resonant null point. This is similiar to placing magnets around a
crystal all pointing inwards. See what effect this has on the resonant
frequencies, voltage, and torsion field. Also the addition of
scalar coils along the magnetic node points would be a good excercise
to see if energy can be added in this fashion. Once leg design is
decided on then we move towards adding the recpricator function, and
completeing all six sides. If fields are not found to operate as
expected we instead regroup.
Phasing
The natural torsion that develops in wire wound CW or CCW, and in the
legs of a pyramid structure should tend to cause the 6 free resonating
circuits to spin predominantly one direction. [Reciprocator function.]
It is hoped that experiment will reveal the natural phasing of a
tetrahedrons complex AC, magnetic, and tempic oscillations. Rather
then try to mentally decipher it, direct measurements are indicated
necessary. Once the iron core resonant system is built and legs
are tunned up, various coils, both torsion and EM, can be used to
stimulate resonance, and a better determination can be made for designs
of the tempic half of the system. The second tetrahedron could likely
be a copper, aluminum, and bismuth core, using scalar canceling
coils, or it can simply be a copper structure to form the complete star
tetrahedron system. The legs will cross the iron tetrahedron at 90
degree angles and either pass through them or at least near enough to
them to interact along there diamagnetic
fields. Lastly is suggested two iron core systems with fields spinning
opposite directions, as controlled probably by coil wind direction. To
produce magnetic fields rotating opposite directions, to increase the
tempic field component of the entire system moving towards the AG type
systems.
The sides of the tetrahedron are thus seen as circles in triangles
where a rotating magnetic field is operating between three voltage
nodes or tips. The magnetic field thus never becomes diffused and never
absorbs energy to become coherent again after fully diffusing. Instead
it precesses avoiding its magnetic dead spot. As
any leg of the system moves into a dead spot of any of its resonant
energy forms at least four other connecting legs will maintain the fields motion
and a smooth rotation will result.
Frequency
Frequencies suggested have ranged from 5.118 Khz to 400 Hz for the leg
resonance. Iron core size, coil wraps, and capacitor values all come
into play in this art at present.
Definitions
reciprocator - uses
a phase differential in two rotating systems to overcome the power
"dead spot" when a spinning force is used to create linear motion. [an
offset of angle or field phase]
magnetricity - magnetic field propagation along an iron wire covered with copper
Credits and References
http://www.totalizm.nazwa.pl/fe_cell.htm Dr Pajak - study of the telekinetic cell [components for OU systems]
Document development and Principles of resonance - David Lowrance c_s_s_p group
Thanks also to Kosol groups and c_s_s_p
group for support and experiments, and special thanks to John Nelson
[tanjmaster2000] for the first device construction of this kind.
The study of Alternate Energy systems is a group effort intended to expand the limits of knowledge of mankind.