Smith Coils
Quadrature Coil Arrangements
12 - 7 - 2014Dave L
Over Unity Section added 12 / 11 / 2014
Wilbert Smith UFO Club Circuit Diagrams
The first time I ever observed two coils setting in Quadrature arrangement.
See the center diagram.
Laminated Core Transformer Coils
The excitation winding is a standard transformer primary circuit fed at low frequency or Audio levels.
The bias winding appears to be wound on the transformer in the opposite direction as the excitation winding.
Here Wilbert is adding a DC current to bias the transformer in the ma range with adjustment, such that the magnetic field polarity will now flip over at a different time then when the AC exciter field reverses direction.
This creates a phase shift in the output [duty cycle] of the transformer in real time. The magnetic field will now spend more time polarized in one direction then the other direction.
[This is an opening to working the Astral and Mental planes, and adjusting the balance between them, in conscious work. Duty cycle adjustment on a scalar canceling coil.]
Since he is deriving this from a power line at 110 volts, rectified and filtered, the voltage may have capacity to fully stop the AC field from reversing the core flux at all.
Quadrature Alignment
[Wilbert's Puzzle]
Wilbert reported "A bridge that is impossible to balance."
The leads marked "Out" should go to zero volts as the 4 magnetic field flux paths, inside the coil, are perfectly balanced by definition.See the arrows above entering the coil. How could this flux pattern create an induced voltage in the coil?
Wilbert reports "Ask any Electronics Engineer, and this should be the way it works, yet this is not what happens."
Wilbert was rather proud to have made this discovery, and stated that several times.
Can you see why this canceling arrangement is impossible to balance, when the 4 legs of magnetic current are induced into the coil?
The coil does not account for the effect of a CW wind on a torsion field. Best guess.
It may be possible to experiment with a secondary wind in the opposite direction, wired in series or parallel with this coil and placed over it,
to locate the ratio of CW to CCW that will produce a torsion field balance as well.
That ratio has never been positively determined for copper wire, but a feel felt best guess has been calculated in the Copper Document.
.
A Deep Scan of Copper
7.26 / 5.22 = 1.39080
Balancing Ratio Identified for Copper mass
1.39080
The CW turns, must be 1.39 longer then the CCW turns, which are stronger.The balance point for the torsion field should land very near this ratio for the two coils.
The diagonal mediator segment may also be of use in this experiment.
24.14 mm
For this we only need make the one coil.
Coil wire length may be any prime number multiple of this length, and the torsion fields may then automatically balance from the inside outwards.
Right off one may think a bifillar wind with canceling connection would do, however that would also generate a Torsion field that would become radiant.
Only dedicated experiment here will produce the science for a complete understanding of the quadrature coil arrangement.
Unlocking this puzzle, may be a great advance for our current scientific field comprehension.
Magnetic Field Canceling
Noteworthy here, a coil we generally believe to have absolutely no electrical significance.How can study and experiment with this coil arrangement, lead into a comprehension we have missed?
The magnetic field from both sides of the transformer, and from top and bottom legs, should all cancel perfectly in this coil.
Yet, according to Wilbert, they do not.
Note the plane of motion for the three fields:
1 -Magnetic field is moving around the iron core, a counter rotating figure 8. This geometric plane is flat to the screen.
2- Electric field is moving at 90 degrees along the center leg of the core, with a scalar canceling modulation winding having an adjustable dc bias.
This geometric plane is horizontal, sticking outwards from the screen.
3- Tempic field coil is wound around the outside at 90 degrees to both, and reacts more like a T field wave.
This geometric plane is running vertical and outwards from the screen.
In the T field coil, there is little current flow over all, but there should be parallel travel of both Electric field tension and mass compression waves.
This coil may have to be adjusted in length to what it terminates to, as the energy along it will manifest as "segments of vibration".
Pi / 2
Over unity, can be achieved by causing vibration in the T wave to transfer into the E field area of the atoms.The simplest way, is to bounce the frequency across a pi/2 ratio between two dimensions.
This is the ratio between the diameter, and 1/2 the circumference of a circle.
Newly created voltage will appear across where ever this ratio is present with T field on both sides.
[See the diode experiments]
Vibration To EM
Why is it important to locate the balancing point in the canceling coils of Wilbert Smiths layout?
Where we set up two Source powered reactive fields to perfectly oppose, such that neither can escape, and neither can accomplish it's goal, the power will begin to soar ever higher on both sides.The closer we can "balance" all three fields, so none can escape, the stronger the force that will rise from each side of the tug of war.
When we then release the fields, far more energy will be present then it took to align and balance the fields to begin with.
When we succeed at a perfect balance, the quadrature winding of the transformer will not have any EM flowing as current,
it will all pass through the copper as mass vibration energy, with a static electric field present, and it will move along at pi / 2 * c velocity.
Within this type of transmission there is no loss, and within it's " power generation from balanced opposition" there is over unity.
Manipulation of the Scalar Canceling Coils energy system
If the new coils are wound exactly from the center outwards with the same number of turns on each side, then all four [magnetic/ inductive] flows should be perfectly canceled within it's one winding.
No Electromagnetic field should be able to propagate this coil system by current teaching, yet must still locate why this does not work as expected..
Reversed Conjugate
At the location above marked "cross over at center" is where we can play with the new energy form, sometimes called Radiant Energy, or vibration at unity levels.
Can we use the earths vibration energy to amplify this field, or in some way amplify the output energy of the system to the load on the right?
My experiment with the density sphere having coils at 90 degrees, leads me to believe it may fully correct a power factor loss between [Power in] and [Load] without the use of any capacitors.
It may fully cancel out the reflected wave from the load, so that it no longer destroys the [Power in] field. I say "may" because I have not done it with iron cores as of yet.
This is based on the information that an Alternating Current EM field, also rotates geometrically with components of voltage and current separated by some angle, [thought to be 90 degrees in real time].
The high frequency component, when the circuit is under stress, [impulse energy] will instantly jump into the 90 degree winding and can be stopped from returning to the [power source] side destructively,
or 180 degrees out of phase to the input power, on it's second jump moving backwards.
Does this transformer remind you of Floyd Sweets VTA?
Also the MEG.
Geometry known to be of value
Square is good.If a coil is set up to be square, it will maximize inductance. Looking at the copper you want thickness to be equal to length.
For the scalar canceling coil, as well it should spread the corners pressure zones of standing waves, to equidistant points and amplify a platonic form effect on a square.
Vibration travels best in segments of equal lengths.
This is a geometry we see in the RM 1 unit with vibration, the clover leaf pattern of vibration.
I would like my transformer core to be as square as possible, that is as deep as it is high, so the canceling coil turns come out square if possible.
Floyd Sweet ended up with similar geometry, having coils in all three planes of a cube.
My density sphere has equal scalar coils in all three planes of a 3D sphere.
It becomes one center of intense compression energy, as it used the 44.5 foot wire lengths in all 3 dimensions in order to fully contain the fields.
Note that in a density sphere, there can be 6 wires passing between two transformers rather then the 4 suggested above.
Every angle of rotation of the field would be covered for T field rotation, however only 4 are necessary for EM power manipulation on a quadrature system.
A Geometric Split Phase Transformer Effect
[The Geometric 90 degree collection coil]
This one may work similar to the last one, using less components.
It worked on the density sphere just fine, and could also pass a square wave without distortion.
I do not believe it is over unity, but it shows how the 90 degree winding can be utilized correctly to improve power factor by physically
grabbing the out of phase voltage component, then wiring it back in phase to the load, using geometry rather then time delay from a capacitor or EM resonance.
A Scalar Canceling Primary Effect
Consider the AC electrical field having three components of geometry in Quadrature, all spinning at the atoms level spherically.[The Density Sphere and Unity - a zero loss transformer]
I made one on a copper sphere about 6" diameter, and another on a crystal sphere about 3" in diameter.
3 each coils are wound, in quadrature geometry.
The input coil must have two windings that are wired to oppose or scalar cancel [bifillar].
The output coils are wired in series in the other two planes of rotation, both setting in quadrature to the primary coils.
Phasing of these two output coils is reversed until a real output power is derived into a load.
The rotational AC fields rotates around the sphere, splitting apart in different direction of rotation.
It was discovered that they again converge in phase at these other two quadrature locations, simultaneously.
Voltage and current will each converge again along these alternate quadrature planes, but maintain 90 degrees of separation.
Thus to extract them both in phase, we must use two coils in the output side to extract and combine them simultaneously.
Placing the energy back into one circuit on the output side.
I believe this causes the reflected counter EMF to cancel out. As a load is applied to the output side, the back EMF cancels in the bifillar winding.
Proton spin is CW from the rear and attached to the mass of the atom. Electron has dual spin, but is predominantly CCW in copper and opposes Proton mass spin.
The 2 90 degree coils catch both of these as they move away from the canceling point on the primary coils.
As the voltage is canceling on the primary coils, there is no or little power drawn on the primary side we can measure.
I believe it is a no loss system, although, I have not taken accurate readings to prove that.
The lamp intensity was used to judge this, and the fact that the power seemed to disappear from the primaries.
I had no real way to measure if power was still being drawn from the mains.
It is believed that a full understanding of the way the AC EM field splits apart and then rejoins spherically, should lead directly into a self sustaining EM transformer system.
If the reflected power is canceled in the primary along with the forwards power, then this coil system should be over unity.
Exactly what is being extracted from the power mains, is unclear.
If you disconnect it from the mains it will no longer work, it does not possess internal oscillation ability or 60 Hz resonance.
[I have however gotten that to happen one time, using an air core toroidal autotransformer.]
The purpose of relating these past examples of experiments on the spherical density spheres is to show,
the 90 degree coil may have a definite function in AC power extraction, yet to be fully utilized for iron core transformers.
Over unity Methods
In order to discover more energy out, then we have coming into a transformer on the primary side, it is necessary to use the T field components of the wave.While the atoms mass pressure field cannot be measured using normal EM test equipment, it can be sensed and tunned, using caliper techniques.
It is harnessed using a scalar canceling coil, with equal and opposite wind geometry, or reversed voltage polarity on the same core.
A Source energy of the universe, which sustains these atoms would have to come through the location of the nucleus of the atoms, via the mass vibrations.
The energy held in the diameter of the atom, is the T wave and has both components of E field and T field in one vector line. See diagram.
Vibration to EM
In this experiment we show how using vibration ratios across diodes or capacitors, the negative voltage will collect at the location where a pi / 2 ratio of vibration is programmed to appear.Operating against this is the diameter value where the positive charge will collect, if both are present. Frequency is used to create electric charge, via a transfer between atomic layers.
This document shows, that without a power supply used at all, small voltages can be generated from diodes, and from grounding bars, into capacitors, consistently using this ratio.
T field waves can be used to pump energy from the atoms mass field, and pop it over into the atoms Electron Proton gap, where an electrical circuit can then use it.
The ratio can be applied directly to time as frequency, or to fractal vibration length, as with the diodes and capacitors.
(1/2 circumference) / diameter = Pi / 2Negative charge vibration rate / (Positive charge vibration rate x 1000)
[~ estimate based on NMR and ESR data]
The reason this ratio works, is that the T wave travels the diameter of the atoms, and the electric field travels the outer circumference, as a transverse wave, or skin effect.
In a current situation, where electric field is moving across many atoms [copper wire] the distance traveled is 1/2 the circumference of the atoms,
and thus we have the pi / 2 ratio clearly indicated as the negative or electrons Electric field side of the ratio.
Diode programming, with calipers, verifies this is the correct ratio.
This is why a scalar canceling coil will boost the voltage, and over unity is possible in electric circuits, where the nuclear mass is forced to become perfectly reactive against itself.
Energy will move from the nuclear mass, first into the Electric Field, and lastly into the Magnetic field, if EM resonance is present, where mass resonance is also present.
So within an EM resonant circuit, if we add a pi/2 T field diversion, it should be possible to amplify the energy of the electric field using the vibration resonance energy.
The positive charge is accessed through the diameter metric, and couples to the mass resonance.
The negative charge is accessed through the [circumference/2] metric.